OW-215N2-X
eXtreme Power 11Na 5Ghz 2×2 +15dBi Outdoor Bridge ( 500mW )
The CERIO OW-215N2-X 500mW eXtreme Power 11Na +15dBi Outdoor Strengthens X edition wireless bridge eliminate hangs carries the newest Cerio CenOS 3.0 Software Core and support Cerio Wireless Management Software (CWMS) and optimizes the operation handling ability promotion use efficiency.
The CERIO OW-215N2-X 500mW eXtreme Power 11Na +15dBi Outdoor Strengthens X edition wireless bridge eliminate hangs carries the newest Cerio CenOS 3.0 Software Core and support Cerio Wireless Management Software (CWMS) and optimizes the operation handling ability promotion use efficiency, regardless of the wireless bandwidth and the wireless load capacity potency and so on all greatly promotes of connection to Wireless Outdoor Network for service providers deploying last mile services to business or residential broadband subscribers. Network administrat efficiencyors can create and centrally manage multiple subscriber service tier using per-subscriber rate limiting features OW-215N2-X may connect to the Wi-Fi mesh or WDS infrastructure and provides the subscriber with an Ethernet connection for a local access to extend the range and increase the performance of a wireless network. The outdoor bridge may connect to the Wi-Fi Mesh or WDS infrastructure and provides the subscriber with an Ethernet connection for a local access. OW-215N2-X also includes PoE, power and data that are supplied to the unit using CAT5 Ethernet cable and supports PoE Bridge transmission functional design. When OW-2xxN2-X/OW-3xxN2 uses the PoE Ethernet (LAN1) port for electricity, it may Bridge (LAN2) port to transmit to a second device using PoE. The Ethernet utilizes the electric power surplus for next PoE PD electricity equipment installment use and enables you to serially connect 48V Passive PoE directly the IPCAM monitoring equipment. This omits the need for constructing additional 48V PoE power sources to supply devices with electricity for terminal IPCAM monitoring equipment
The Software Built-in : CenOS 3.0 Introduction
CERIO’s GS Firmware uses the CenOS 3.0 core . The firmware’s main functions are Wifi application for Pure WiFi Access Point (Includes AP+WDS) and Point to Point / Multi Point WiFi Bridge and Bridge + Repeater Extension WiFi AP and WISP/CPE for Router + WiFi Repeater AP functions . The CenOS 3.0 core’s operational mode supports Pure AP with WDS Mode / Pure WDS mode / Client Bridge + Universal Repeater Mode and WISP/CPE Repeater +AP mode. The CenOS 3.0 features that simplify deployment and reduce cost for continued maintenance of the indoor Access Point . The Cerio CenOS is undoubtedly your wifi application best choice.
Note: OW-215N2-X supports only Pure AP Mode , Pure WDS Mode, CPE Mode, Client Bridge + Universal Repeater Mode and CPE + AP Mode mode through Cerio’s CenOS3.0 software.
OW-215N2-X CenOS 3.0 Software key Features
- Operation Modes : Pure AP Mode , Pure WDS Mode ,Client Bridge + Universal Repeater Mode and WISP/CPE + Repeater AP Mode
- Maxmum Security with 802.1X, WAP, and WPA2
- Supports wireless IGMP the v1/v2/v3 function, may pass on in the wire the immediate video and music wrapped gift
- 8 Multiple-ESSID and supports the IAPP wireless network roaming function
- Supports RIP and the OSPF route function (Dynamic Routing)
- Support Static Routing and RIP and OSPF Dynamic Routing by CPE mode
- Layer-7 Protocol Filter and Content Filter by CPE mode
- QoS(Quality of Service) for bandwidth management and traffic prioritization
- Support IEEE802.1d Spanning Tree
- Ping Watchdog function support
- Support Hardware chipset base Watch Time Dog , The OS will be reboot by automatically before crash
- Software UI support Auto reboot setting function , Can by Hour/Daily/Weekly to setting software Auto reboot
- Built-in Cerio CenOS3.0 software interface allows for communicating with Cerio Wireless Management Software (CWMS) and CERIO AM-Series AP Management WLAN Switch or Access Controller hardware
device of network management servers - Support Web management and SNMP MIB-II and CLI via Telnet and the SSH interface Management function
- Provide Traffic Monitor and Graphical GUI Status Interface
OW-215N2-X CenOS 3.0 Operation Mode Applications
Pure AP Mode & AP/ AP+WDS Mode
- It can be deployed as a tradition fixed wireless Access Point
- It allow wireless clients or Stations(STA ) to access
- This enables the wireless interconnection of Access Point in an IEEE802.11 network and accept wireless clients at the same time .
Pure WDS Mode (Repeater)
- This enables the wireless interconnection of Access Point in an IEEE802.11 network
- It allows a wireless network to be expanded using multiple access point without the need for a wired backbone to link them
- This also be referred to as repeater mode
- It can not allow wireless clients or Stations (STA) to access
Client Bridge + Universal Repeater Mode
- It can be used as an Client Bridge + Universal Repeater to receive wireless signal over last mile applications, helping WISPs deliver wireless broadband Internet service to new residential and business customers.
- In this mode, OW-200N2-X is enabled with DHCP Server functions. The wired clients of OW-200N2-X are in the same subnet from Main Base Station and it accepts wireless connections from client devices
CPE (WISP) +AP Mode
- It can be used as an Client Bridge + Universal Repeater to receive wireless signal over last mile applications, helping WISPs deliver wireless broadband Internet service to new residential and business customers.
- In this mode, OW-215N2-X is enabled with DHCP Server functions. The wired clients of OW-215N2-X are in the same subnet from Main Base Station and it accepts wireless connections from client devices
OW-215N2-X CenOS 3.0 Software Specifications
Networking( In CPE mode support )
- Static IP, Dynamic IP(DHCP Client) and PPPoE on WiFi WAN Connection
- Support VPN Pass Throughput ( PPTP , IPSec , L2TP )
- PPPoE Reconnect : Always on , On demand, Manual
- MAC Cloning
- DHCP Server
- IEEE802.3 Bridging
- Masquerading (NAT)
- Virtual DMZ, Virtual Server (IP / Port Forwarding)
- Support IP / MAC Filter
( In other mode support )
- Proxy DNS ,Dynamic DNS ,NTP Client
- Bandwidth trafic Shaping
Wireless Feature
- Transmission power control : Layer 1~9
- Channel selection : Manual or Auto
- No of associated clients per AP : 32
- Setting for max no associated clients : Yes
- No. of BSSID (Virtual AP ) : 8
- No. of Max. WDS setting : 8
- Preamble setting : Short/ Long
- Setting for 802.11a/n mix or 802.11a only
- Setting for transmission speed
- Dynamic Wireless re-transmission
- IEEE802.11f IAPP (Inter Access Point Protocol), hand over users to another AP
- IEEE 802.11i Preauth (PMKSA Cache )
- IEEE 802.11h – TPC(Transmission Power Control) and DFS(Dynamic Frequency Select)
- IEEE 802.11d -Multi country roaming
- Channel Bandwidth setting : 20MHz or 20/40MHz
- HT Tx/Rx Stream selection : 1 or 2
- A-MSDU and A-MPDU support
- Maximal MPDU density for TX aggregation setting
- Short Slot support
Authentication/Encryption (Wireless Security)
- Blocks client to client discovery within a specified VLAN
- WEP 64/128 bit /EAP-TLS + Dynamic WEP , EAP-TTLS + Dynamic WEP
- PEAP/MSPEAP + Dynamic WEP
- WPA-PSK/TKIP,WPA-802.1x/TKIP, 802.11i WPA2-PSK/CCMP/AES 128/256bit,WPA2 (802.1x /CCMP / AES 128/256bit )
- Setting for TKIP/CCMP/AES 128/256bit (ASCII 63 & HEX 64 )key’s refreshing period
- Hidden SSID broadcast support
- Access Control list (ACL) by MAC Address
- No. of registered RADIUS servers : 1
- VLAN assignment on BSSID
Quality of Service
- Download and Upload traffic control
- Packet classifications via DSCP (Differentiated Services Code Point)
- Control Policy by IP/IP Ranges/ MAC/ Service
- Layer-7 Protocol Support
- Traffic Analysis and Statistics
- DiffServ/TOS
- IEEE 802.11p/COS
- IEEE 802.1Q Tag VLAN priority control
- IEEE802.11e WMM
Management
- Web-Based management interface
- Intuitive Web Management Interface
- Support Firmware Upgrade via Web , Reset to Factory Defaults,
- Support Profiles Configuration Backup and Restore
- Remote Link Test – Display connect statistics
- Support SNMP v1/v2c/v3 , MIB II
- Administrative Access : HTTP and HTTPS
- UPnP (Universal Plug and Play) by CPE mode
- NTP Time Synchronization
- SNMP Traps to a List of IP Address
- DHCP client
- Support Event log
- Support CLI access via Telnet and SSH
OW-215N2-X Hardware Key Features
- IEEE 802.11n Compliance in 2Tx / 2Rx Design
- Enables Bandwidth of up to 300Mbps(Tx), 300Mbps(Rx) link rate
- Support IEEE 802.11n and 802.11a, Operates in the 5GHz ISM Band
- 500mW eXtreme High Power at 5Ghz
- Built in +15dBi , 5GHz (H65, E35) Directional Panel Antenna
- Topology : Point to Point , Point to Multi Point
- Support Over load current protection for the board design . and 3 LEDs Wireless Signal Strength
- Weather-Proof Housing (IP67/ 68 Approved)
- Weater-Proof M-13 RJ45 Connector
- Support Power over Ethernet (PoE) & PoE Bridge by LAN Port function.
- Wide Range Voltage Input PoE Power support (12-68VDC)
- Build-in lightning arrester (15kV ESD)
OW-215N2-X Hardware Application
OW-2015N2-X eXtreme Power 11Na 5Ghz 2×2 +15dBi Outdoor Bridge with die case weatherproof housing utilizes built-in 5 GHz 2×2 15dBi directional antennas and hardware a lightning arrester (15kV ESD) design.
PoE Bridge application
The CERIO OW-200N2-X / OW-215N2-X Design in for PoE Bridge hardware function, the PoE Bridge function support provide power source to next PoE AP or next PoE passive PoE(PD) Device . Passthrough the PoE surplus electric power to for next OW-2xxN2-Series / OW-3xxN2-Series AP or other 48V PoE the electricity PD installment use, will be structure become very convenience.
Use U-Clamps for Easy Pole Mount Installation
| Application Software | |
| OS System Compatible edition | Cerio CenOS 3.0 Software Core |
| Specifications | |
| Network Standards Conformance | IEEE 802.11 a/n compliant |
| IEEE 802.3 / IEEE 802.3u | |
| IEEE 802.11a/n compliant | |
| IIEEE802.11f IAPP (Inter Access Point Protocol), | |
| hand over users to another AP | |
| IEEE 802.11i Preauth (PMKSA Cache ) | |
| IEEE 802.11h -Transmission Power Control | |
| IEEE 802.11d -Multi country roaming | |
| Ethernet Configuration | Die Case Housing Weatherproof Protection Ethernet Connector x 2 (Power over Ethernet PoE in and PoE Bridge Port ) |
| LED Indicators | ETH1 LEDx1, |
| ETH2 LED x1 | |
| PWR LED x1 | |
| LEDs Wireless Signal Strength x 3 ( only for Client signal bridge) | |
| Wireless Specifications | |
| Data Transfer Rate | IEEE802.11a :6/ 9/ 12/ 18/ 24/ 36/ 48/ 54Mbps (auto sensing) |
| IEEE801.11n(draft 2.0) : 300Mbps (Tx), 300Mbps (Rx) | |
| Frequency Range | IEEE802.11a : |
| 5.150 – 5.350 & 5.725 – 5.825 GHz(USA) | |
| 4.900 – 5.250 GHz(Japan) | |
| 5.150 – 5.350 & 5.470 – 5.725GHz (Europe ETSI) | |
| IEEE802.11n : | |
| 5.150 – 5.350 & 5.725 – 5.825 GHz(USA) | |
| 4.900 – 5.250 GHz(Japan) | |
| 5.150 – 5.350 & 5.470 – 5.725GHz (Europe ETSI) | |
| Channel Spacing | IEEE802.11a : 20MHz |
| IEEE802.11n : 20/40MHz | |
| Media Access Protocol | CSMA / CA with ACK |
| Modulation Method | IEEE 802.11a : OFDM with BPSK, QPSK, QAM and 64QAM |
| IEEE 802.11n : BPSK, QPSK, 16-QAM, 64-QAM | |
| Operating Channels | I IEEE 802.11a : |
| US : 12 (CH: 36, 40, 44, 48, 52, 56, 60, 64, 149, 153, 157, 161) | |
| Japan : 4 (CH: 34, 38, 42, 46) | |
| ETSI : 19 (CH: 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140) | |
| IEEE 802.11n @ 5GHz : | |
| US : 12 (CH: 36, 40, 44, 48, 52, 56, 60, 64, 149, 153, 157, 161) | |
| Japan : 4 (CH: 34, 38, 42, 46) | |
| ETSI : 19 (CH: 36, 40, 44, 48, 52, 56, 60, 64, 100, | |
| 104, 108, 112, 116, 120, 124, 128, 132, 136, 140) | |
| Transmit Power Variation | Max : 27dBm |
| Receiver Sensitivity | Max : -97dBm |
| Environmental & Mechanical Characteristics | |
| Operating Temperature | -25 °C ~ 70 °C |
| Storage Temperature | -30 °C ~ 80 °C |
| Operating Humidity | 100% Non-Condensing |
| Storage Humidity | 100% Non-Condensing |
| Built-In Antenna | +15dBi Dual Polarziation Directional Antenna ( H : 65 , E : 35) |
| Form Factor | Wall Mount and Pole Mount Ability, Die-Cast aluminum Enclosure withIP67/IP68 Rating |
| System Power Consumption | 9Watt |
| Power Supply | Fast Ethernet PoE Injector , Support Power Over Ethernet (48V) input (PoE Power Injector) |
| AC Input : 110-220V | |
| Input Power | 12~68 Voltage Wide Range PoE in |
| Dimensions | 102 x 162 x 58 mm |
| Unit Weight | 645g |
| Certifications | CE ，FCC，NCC、ROHS compliant |
| Package Content | |
| OW-215N2-X Main Unit | x1 |
| POE Power Injector kit (Power Supply) | x1 |
| Wall/Pole Mounting Bracket | x1 |
| CD Manual | x1 |
| Warranty Card | x1 |
